This tailgate friendly motorcycle loader allows you to load your bike quick and easy with its dual heavy duty 12 volt winches. Two winches gives the loader complete control of angle and allows for waist height cleaning and service work of your bike.
Tech Specs
Aluminum Slide Construction (No Rust)
Tailgate friendly (Allows installation of tailgate once bike is loaded)
Sealed Ball Bearing rollers
Sealed all weather winches
Dual winches (allows you pull out bike and clean / service at waste height)
Quick disconnect system allows you to remove loader when not in use
This Motorycle Loader takes all the work out of loading or unloading your full size bikes. This Hydraulic Loader features a 12 volt powered Hydraulic Pump that runs directly off your truck Battery. The Hydrulic Pump is made of the best materials and workmanship featuring Made In The U.S.A. quality. This Sturdy Pump ensures years of trouble free use without any need to replace worn out cables that can get old, split and eventually fail droping or damaging bike. This Hydraulic Motorcycle loader is a step above the traditional loaders that have small winches, cables and pulleys. The entire loading system is made in our Phoenix Az, Factory on a precision C&C Plasma cutting table, Raw materials are formed on our C&C press and then Powder coated to ensure years of trouble free use.
Wheel holding system and simple to use Remote Control allow for easy trouble free loading and unloading of your Bike. If your looking for a quality dependable system, this is the Motorcycle Loader you can trust to safely and easily load and unload your Ride!
Specify trike loader or two wheel loader when ordering!
Winch Motorcycle Loader
The Motorcycle Loader, easily and safely loads and unloads your motorcycle. From the ground to the back of your vehicle, one person can safely load and unload their bike while never getting on the motorcycle by pushing a button on a remote control switch. The Motorcycle Loader allows for storage and still allows you to pull a boat or trailer. The unique configuration fits into most full-size or mid-size pick up truck beds and has the ability to be installed in very short truck beds such as Chevy Avalanche or Honda Ridgeline.
The motorcycle lift will extend past the end of the bed and carry the load safely without damaging the tailgate. The Motorcycle Loader is not a permanent modification, it consists of a modular, 3 piece construction for easy installation and removal by one person in minutes!
Motorcycle Loader includes quality features like an extremely strong, structural steel design capable of loading 1000 pounds. The wheels and rollers are industrial grade nylon and there are no bearings to grease or maintain. The carriage tracks are slotted to allow for rain water, dirt and debris. The 2500 LB capacity winch with a 5000 LB capacity strap operates on a 12 volt DC system.
The Mountain Master Motorcycle Loader is a simple, reliable design that is very easy to operate and requires very little maintenance.
Trike loader option
Handles the Largest Motorcycles with Ease
Fast and Simple – One Person Operation
Strong Structural Steel Frame
Tough Powder-Coat Paint for Durability
2,500lb. Winch with Safety Brake and 12' Remote
Two Units can be Installed in a Standard Width Truck
Also available for Jet Skis, Wave Runners, Snowmobiles, and ATV's
Fits almost any truck or RV
8 foot truck beds must remove tailgate
Easy Installation and Removal
Image:
Mountain Master Motorcycle Loader
Width – 23½” (Two units will fit between the wheel wells of a standard truck) Length – 95” (Fits in an 8’ bed truck with the tail gate closed) Weight – Approximately 330 pounds (Comes apart easily into 3 manageable pieces) Winch - 2500 pound capacity unit with integrated safety brake Winch strap – Heavy duty cable Winch control – 12’ remote (can be disconnected and stored in the truck) Bed attachment – Rivet Nut type fasteners that are installed in the bed and do not require attachment to the frame. Fasteners are installed from the top and does not require access from the bottom of the bed Base – Low friction skids for easy removal without damaging the truck bed Bed Height – Tested for truck bed heights of up to 39”. For higher beds, please inquire. We offer to test and certify other heights as required
